You are describing snipe
The symptom goes like this. You run a board through your thickness planer. Most of it comes out beautifully. But the first few inches and the last few inches are cut slightly deeper than the rest, so the board has a shallow dip at each end. Run your fingers along it and you can feel the step. Hold a straightedge against it and you can see the gap.
It happens on every board. It happens whether you go slowly or quickly. It happens on boards short enough that they never hang off the end of the machine.
That is called snipe, and if you have never heard the word before, you are in good company. A lot of people run into it long before they find out it has a name, which makes it hard to search for.
It is not your fault
Worth getting this out of the way early, because most people assume they have done something wrong or bought a faulty machine.
Snipe is normal on benchtop planers. Every brand does it to some degree. It is a consequence of how these machines are built rather than a defect in your particular one, and no amount of being careful with the board will fully remove it.
One owner was concerned enough to send his planer back to the manufacturer. Technicians made their own test cuts and told him the snipe was within acceptable limits for the machine, and returned the test board to show him. That is one person's account of what he was told, but it fits what thousands of owners experience.
So if you were worried you got a bad unit, probably not.
What is actually happening
Inside your planer, two rubber rollers hold the board down while a spinning cutterhead takes a slice off the top. One roller sits before the cutterhead and one sits after it.
When the board is fully inside the machine, both rollers are pressing on it. Everything is balanced and the cut stays even.
But at the very start of the pass, only the front roller has hold of the board. At the very end, only the back roller does. In those two moments the forces inside the machine change, the parts holding the cutterhead flex by a tiny amount, and the cutter ends up a few thousandths of an inch deeper into the wood than it should be.
A few thousandths is not much, which is why the dips are shallow. It is also enough to show up on a glued panel or a visible surface, which is why it bothers people.
The key thing to understand is that the board is not moving. The machine is flexing. That explains why it still happens on a short, well supported board, and why longer tables on their own do not make it go away.
What people do about it
There are a handful of standard approaches. All of them help, none of them is free.
- Cut your stock long and trim the ends off. The simplest answer. You lose a few inches of lumber on every board.
- Run scrap boards before and after. The rollers pick up and release the scrap instead of your good piece. This works reliably and costs you wood, time and handling on every single pass.
- Butt boards end to end. Same idea without the scrap. Only the first and last board in the run get sniped. Useful when you have a batch, useless for one board.
- Lift the ends slightly by hand as the board goes in and comes out. This genuinely helps, and it depends on your feel every time, which makes it hard to repeat.
- Support the board properly. Roller stands or extension tables stop long stock from tipping. Worth doing regardless, though it will not remove snipe by itself.
Most woodworkers settle on one of these and live with it. That is a perfectly reasonable place to land, especially if you mostly build things where a few thousandths at the ends never shows.
Before you go further, check it really is snipe
Snipe is a deeper cut at both ends, running the full width, repeating every time. If what you are seeing is lines running the length of the board, or rough patches around knots, or a mark somewhere in the middle, that is a different problem with a different fix. Our guide to reading the marks on your board sorts them out.
If you want to go deeper
Once the word makes sense, the rest of the material opens up. Six techniques for reducing snipe covers the practical side, and why the classic tricks are workarounds explains what each one is really doing and where each one runs out.
If you own a DeWalt DW735 specifically, there is also a mechanical route: limiting how deeply the feed rollers press into the board, which shrinks the force change that causes the whole problem. We cover that in our post on roller adjustment.