Start with where the mark is
Snipe has a signature, and it is a narrow one. A consistent deeper cut in roughly the first and last three to six inches of the board, running the full width, repeating on every board you run.
If what you are looking at does not match that description, it is probably not snipe, and the usual snipe advice will not help you. Work through the list below before you change anything.
This matters more than it sounds. We regularly hear from people who spent weeks on sacrificial boards and table adjustments for a problem that turned out to be a nicked blade.
The quick version
| What you see | What it usually is |
|---|---|
| Deeper cut at both ends, full width | Snipe |
| Thin raised lines running the length | Nicked blades |
| Rough torn patches at knots or figure | Tear-out |
| A band of over-cut partway along | Feeding hesitation |
| One edge thicker than the other | Head not parallel to the bed |
| Regular ripples along the length | Feed speed setting |
| Random scratches or burnished streaks | Debris, pitch, or a burr |
Working through them
Deeper cut at both ends
This is snipe. It is caused by the load on the machine changing when it goes from both feed rollers carrying the board to only one, at entry and at exit. The carriage flexes a few thousandths and the cutting plane shifts closer to the board.
It is consistent, it is measurable, and it happens on short boards that never overhang the table, which rules out the common assumption that the board is drooping. Our full explanation of the mechanism covers it properly.
Thin raised lines running the full length
Nicked blades. A small chip in a cutting edge leaves a corresponding ridge every time that part of the knife passes. The line will be in the same position across every board.
On straight knives, shifting one blade slightly sideways moves the ridge off the previous one and often makes it disappear. Rotating or replacing the knives solves it properly. With a helical head, rotate the individual insert at that position.
Rough or torn patches at knots and figure
Tear-out, where the knife lifts fibers rather than cutting them. Usually a grain direction problem, sometimes a depth of cut problem.
Try running the board the other way round, take lighter passes, and slow the feed. Dampening the surface lightly before the final pass helps on difficult stock. This is the one problem a helical cutterhead genuinely solves, which we cover in our post on helical heads.
A band of over-cut somewhere in the middle
The board slowed or stopped while the cutterhead kept turning. Feeding problem, not a cutting problem.
Causes: glazed or dirty feed rollers, a bed that needs waxing, too heavy a cut for the width, or a cold shop stiffening the rubber. Clean the rollers with mineral spirits, wax the bed, and take a lighter pass. If it is winter, read why cold shops make this worse.
One edge thicker than the other
The cutterhead is not parallel to the bed. Measure both edges of a wide board with calipers after a pass. A consistent difference across the width, independent of position along the length, confirms it.
This is a separate adjustment from anything to do with rollers, and it is worth fixing first because it will confuse every other measurement you take.
Regular ripples along the length
Scalloping from the feed rate. Each knife leaves a shallow arc, and the faster the board moves the further apart those arcs sit.
The DW735 has two feed speeds. The faster one is for hogging material off, the slower one for finish passes. If your final pass is on the fast setting, switch it and the ripples will tighten up to the point of invisibility.
Random scratches or shiny streaks
Something is dragging. Chips recirculating, pitch built up on the bed or the rollers, or a burr in the casting behind the cutterhead. Unplug the machine, look and feel along the surfaces the board touches, and clean or stone as needed.
One test that settles most arguments
Take a board longer than you need, run it, then measure thickness with calipers at four points: one inch from each end, and two spots in the middle. Write the numbers down.
If the ends measure thinner than the middle by a consistent amount, you have snipe and you now know how much. If the numbers are even and your complaint is about surface appearance, your problem is in the cut quality rather than the thickness, and that is a different list of fixes.
Having the number also tells you whether it is worth doing anything. Plenty of people chase snipe that measures under a thousandth, which will vanish in sanding.
If it is snipe
Once you have confirmed it and measured it, the question is whether to manage it on every pass or change what the machine does. Sacrificial boards and careful lifting work, at the cost of doing them forever. The alternative is controlling how deeply the feed rollers press into the board, which is what drives the load swing in the first place.
The DW735 gives you no adjustment for that from the factory. Our post on roller adjustment explains why, and our Planer Snipe Fix Kit adds it, with a 30 day money back guarantee.
If it turned out to be a nicked blade, we are glad you found out before buying anything.