The four Phillips screws holding the feed roller brackets are the hardest part of any DW735 roller job. They come from the factory brutally tight, often with thread locker, and the heads are soft enough to round out on the first try. This is the method that gets them out, and it works even on heads that are already chewed up.
Why these screws fight you

That is what happens on the first attempt, and it is not a skill problem. Three things stack against you:
- Factory torque. These are driven on an assembly line and never meant to come out. They may even have thread locker on them.
- Soft heads. The Phillips recess is shallow and the steel is soft. A Phillips driver is designed to cam out under load, which is useful on an assembly line and terrible here.
- No leverage. The screws sit up under the carriage with the machine flipped over. You cannot get your shoulder behind a screwdriver, so all your force goes into twisting instead of pushing.
The fix is not more torque. It is holding the bit hard into the screw while you turn it, so it physically cannot cam out. The planer already has a tool that does this, and it is the height adjuster.
What you need
Nothing exotic. Most of this is already on your bench:
- A scrap block of hardwood, roughly 3 x 3 x 3/4
- A 1/16" and a 1/2" setup block, or any shims that measure close to those
- A 1/4" box wrench or a small ratchet
- A 1/4" hex Phillips bit, PH2, the longer the better
A fresh bit matters more than you would think. A worn PH2 sits shallow in the recess and rounds the head on the first pull.
Build the base
The whole method depends on the bit sitting dead square in the screw and not wandering. That means building a small platform under it first.
Cut a kerf in the block. One saw cut across the face, deep enough (~1/4 in.) for the edge of the planer bed to clear, so the block can sit flat.

Set your height with the gauge blocks. The 1/16" goes on the planer base, the 1/2" on the side.

Stack the block on top.

You now have a solid, flat platform directly under the screw you are working on, at roughly the right height. Everything above it will stay put instead of wobbling.
Pinch the bit into the screw
This is the part that makes the difference.
Seat the Phillips bit into the screw head first, by hand. Then crank the planer's height adjuster down until the block underneath rises and pinches the bit up into the screw.

Snug it until the bit is genuinely loaded, not just touching. The bit is now trapped between the screw above and the block below, with nowhere to cam out to. That clamping force does the job your arm cannot do from under the machine.
Now put the 1/4" box wrench over the hex shank of the bit and turn it. As far as the wrench is concerned, the bit is the fastener. All of the turning force goes into the screw instead of into the head.
If the bit will not sit square in the screw, adjust your shim stack rather than forcing it. A bit entering at an angle will round the head no matter how much pressure is on it.
Turn it the right way
Stop here for a second, because this is where people destroy a screw they had already won.
The screws are upside down. Everything your hands know about which way loosens is now backwards. Righty-tighty is reading from above the screw, and you are looking at it from below.
Work out the direction before you put any force on it. These two photos show the wrench travel:


Move the wrench in a short stroke. You don't have to go far, it is just to break it loose.
The first break is the hard one. Once a screw cracks loose it usually spins out easily, and you can back the carriage off and finish by hand. Then move to the next screw and build the stack again underneath it.
If the head is already chewed up
Most people find this guide after they have already rounded out at least one screw. The good news is that the pinch method is exactly what rescues those.
A rounded Phillips still has material in it. What it has lost is the ability to hold a bit under twisting load, which is the one thing the carriage pressure replaces. Clamp a fresh PH2 in hard enough and a head that spun freely under a screwdriver will usually still break loose.
If the recess is truly gone, stop trying to drive it and go at the head from the side instead. The heads stand proud enough to grab. A pair of lineman's pliers, or a small pipe wrench, will bite into the outside of the head and turn it when no bit will hold. It mangles the head further, but that screw is coming out and going in the bin either way.
No drilling, no extractors. You do not need them on this machine, and a drill bit wandering off a screw head and into the casting is a much bigger problem than the screw ever was.
One thing worth saying plainly: a destroyed bracket screw is not the end of the job. They are a standard fastener and DeWalt sells replacements. Nobody has had to retire a planer over this.
Why this guide exists
A customer left us a one star review that said he could not get the roller brackets off to even try the kit. He was right to be annoyed. We shipped a product whose very first step is a fight, and we never wrote down how to win it. That is on us, and this page is the fix.
Two changes are coming out of it. This method is going into the printed installation guide, so nobody has to go looking for it. And the upgraded kit will include a machined base block that replaces the shim stack and the shop-made wood block entirely, so the setup is one piece instead of three.
If you are stuck partway through right now, email us before you force anything. We would much rather spend ten minutes on the phone with you than have you fight it alone.