Your DW735 Crank Got Hard to Turn. Stop Cranking.

Stop before you force it

If the height crank on your DeWalt DW735 has gone stiff, or will only turn a quarter turn, or has stopped entirely, put the handle down. This is the one situation on this machine where pushing harder makes the repair substantially worse.

The crank drives all four threaded posts through a chain and four sprockets, so that the carriage rises and falls level. Force it against a jam and the chain can skip a tooth. When that happens the posts are no longer in time with each other, the carriage sits out of parallel with the bed, and getting it back means pulling covers, taking the chain off, and bringing all four posts to the same height by measurement. Owners who have done it describe it as doable and not fun.

Unplug the machine. Then work out what is actually in the way.

Three things to rule out first

All three take a minute and none requires taking anything apart.

The turret stop. The DW735 has a rotating depth stop that prevents the carriage going below a set thickness. The manual is explicit that you should not force the crank below the level the turret stop indicates, and warns of permanent damage if you do. If your crank stops dead at one particular height and turns freely everywhere else, check the turret before anything else. This catches a lot of people, especially on a secondhand machine where the previous owner left it set.

A crank that has always been stiff. The DW735 crank is not light. It drives four lead screws under the weight of the carriage, and some resistance is normal. If yours has felt the same since the day you unboxed it and moves evenly through the whole range, you may not have a problem.

A machine that has been sitting cold. Lead screws that have gone months without moving in an unheated shop get sticky. Run the carriage slowly through its full range a few times before concluding anything.

What is almost always wrong

Wood chips packed into the lift mechanism.

The DW735 has a motorized impeller that throws chips out through the exhaust port. When that path stops working properly, the chips have to go somewhere, and where they go is into the body of the machine. They collect around the chain and the sprockets that sit on top of the four posts. Once a sprocket is packed solid, the crank stops.

So the real question is not how to clean it out. It is how the chips are getting in, because otherwise you will be doing this again in a month.

Four ways chips get inside

In rough order of how often they turn out to be the answer.

1. The dust shroud is not sealed. Three red thumb screws hold the shroud down over the cutterhead. If they are not run all the way in, or one was missed, the shroud does not seal and chips blow straight past it into the machine.

This one has a trigger attached: it usually shows up a few weeks after a blade change, because changing knives means taking that shroud out and putting it back. If your crank went heavy some time after you last rotated or replaced blades, check the three thumb screws before you check anything else. It is the cheapest possible fix and the easiest thing in the world to leave half done when you are keen to get back to work.

2. The chute or shroud is deformed. Same symptom, different cause. A chute that has been bent, or a shroud that has warped or lost its seal, leaks in the same way and will not seal no matter how carefully you tighten the thumb screws. Look along the mating edges in good light.

3. The chip path is backing up downstream. A clogged chute, a full collector, or something attached to the exhaust port that cannot move the volume this machine produces. The impeller keeps pushing and the chips find another way out. This is the most common underlying cause and it is covered in should you connect a shop vac to a DW735.

4. The impeller housing has worn through. The housing is two plastic halves meeting along a seam, and that seam can wear open. The gap is small and usually invisible until the housing is off. With a hole there, the impeller blows chips into the interior continuously and no amount of cleaning keeps up. Owners have reported this on machines well over a decade old, and a replacement housing from a service center fixed it. A cracked housing does the same thing.

Getting in, the documented way

The manual covers more of this than most owners realize, and the first level of access is genuinely easy.

  1. Top cover. Four screws, taken out with the T-wrench that came with the machine. The cover lifts straight off.
  2. Dust shroud. Three red thumb screws from inside the top. The shroud lifts out and the cutterhead is exposed.
  3. Fan housing. The manual's own procedure for reaching the fan: with the cover and shroud off, remove the screws and clips around the fan housing and set it aside. The fan is then exposed for cleaning.

That gets you to the shroud seal, the chute and the impeller, which is three of the four causes above. It is a ten minute job with one wrench.

Worth knowing before you panic: the planer will not run with the top cover off. The cover presses a safety switch, and the manual says plainly that the machine will not operate unless the cover is placed correctly. If it refuses to start after you reassemble, that switch is the first thing to check rather than the motor.

The access doors

There are small access doors around the gear on the exhaust side of the machine. They exist because DeWalt knew that gear would pack with chips, and they let you clear that one spot without taking the main cover off.

If your jam is on that side, try there first. Owners who clean regularly use them often enough that the doors themselves wear loose over time, which tells you something about how often this happens.

The full job, and whether it is worth it

Reaching all four post sprockets is a different proposition, and it is worth being honest about the scope before you start.

The part you have to remove is not the top cover you already took off. It is the large yellow moulded cover that wraps all four sides, and it has to be lifted up and over the four chrome posts to come away. The depth gauge on the front right post has to come off first. Owners also remove the side panels to make it manageable.

With that off, the chain, the four sprockets and the posts are exposed, and you can clean everything properly, take the chain off if you need to, and set the posts back in time.

This is an hour or two with the machine on a bench, not a quick tidy-up. If your jam cleared at the shroud and chute stage, you do not need to go here. If the crank is still stuck after the easy access, or the chain has already skipped, you do.

Cleaning and lubrication

Vacuum and brush rather than relying on compressed air alone, which tends to relocate chips rather than remove them. Wire brush any pitch or corrosion off the threaded posts.

Lubricate with a dry lubricant. Dry PTFE or a wax-based product is right. Grease and oil both read as helpful and both turn into chip magnets, which is how a machine ends up back on the bench a month later.

Run the carriage up and down through its full travel before the covers go back on, so you know you actually fixed it.

If you already forced it

If the crank turns now but the carriage feels wrong, or the machine started planing a taper across the width that it never had before, the chain probably jumped and the posts are out of time with each other.

The fix is to get the covers off, remove the chain, and bring all four posts to the same height by measurement rather than by eye. Taking the caps off the post tops and laying a steel rule across them is one way owners do it. Calipers against a known reference is another. Then refit the chain.

It is tedious and it is not beyond anyone willing to open the machine in the first place. Expect to check your work with a test board and go round again.

Keeping it from happening again

  • After every blade change, check that all three shroud thumb screws are fully home. This is the single highest-value habit on this list.
  • Empty whatever catches the chips before it is full, not after.
  • Make sure what you have attached to the exhaust port can handle the volume.
  • Clear the access doors on the exhaust side periodically rather than waiting for a symptom.
  • Take the top cover off once a year and look. Chips around the chain means something upstream is leaking.

While the covers are off

A seized crank is a maintenance problem and it has nothing to do with the quality of your cut. But a machine that has run long enough to pack a sprocket has usually also had its feed rollers glazed with pitch and its roller rubber hardened with age, and both of those change how the machine behaves at the ends of a board.

If your planer has been sniping more than it used to, why the DW735 snipes and what actually changes it explains what drifts and why there is nothing on this machine to set back.

Back to blog

Leave a comment